Comparative study of machining technology selection to manufacture large-size components of offshore constructions

• Autorzy: Deja M. , Siemiatkowski M. , Sender P.
• Języki publikacji: EN

Abstrakty

EN

The focus of this paper is on process planning for large parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centres. The analysis of machining heavy mechanical components used in off-shore constructions has been carried out. Setup concepts applied and operation sequences determined in related process plans underwent studies. The paper presents in particular a reasoning approach to setup sequencing and machine assignment in manufacturing large-size components of offshore constructions. The relevant reasoning mechanism within a decision making scheme on generated process plan is shown based on a case study derived from the offshore sector. Recommendations for manufacture of selected exemplary and typical parts were formulated

• Wydawca: -
• Czasopismo: Polish Maritime Research
• Rocznik: 2017
• Tom: 24
• Numer: Special Issue S1
• Opis fizyczny: P.38-45,fig.,ref.

Twórcy

autor

Deja M.

• Department of Manufacturing Engineering, Faculty of Mechanical Engineering, Gdansk University of Technology, 11/12 Narutowicza St., 80-952 Gdansk, Poland

autor

Siemiatkowski M.

• Department of Manufacturing Engineering, Faculty of Mechanical Engineering, Gdansk University of Technology, 11/12 Narutowicza St., 80-952 Gdansk, Poland

autor

Sender P.

• Elektromontaz-Polnoc Gdynia S.A.(EPG), Gdynia, Poland

Bibliografia

• 1. Celano G., Costa A., Fichera S. and Santangelo B.: Pallet configuration for approaching mapping requirements on devices, Chapters 6 in: Design of flexible production systems: methodologies and tools, Tolio T (Ed.), Springer -Verlag 2009.
• 2. Choi J.P., Min B.K. and Lee S.J.: Reduction of machining errors of a three-axis machine tool by on-machine measurement and error compensation system. Journal of Materials Processing Technology, Vol. 155-156 (2004), pp. 2056-2064.
• 3. Deja M. and Siemiatkowski, M.S.: Feature-based generation of machining process plans for optimised parts manufacture.Journal of Intelligent Manufacturing, Vol. 24 (2013), pp. 831-846.
• 4. Gologlu, C.: Machine capability and fixturing constraints-imposed automatic machining set-ups generation, Journal of Materials Processing Technology, Vol. 148 (2004), pp. 83-92.
• 5. Groover M.P.: Fundamentals of modern manufacturing, Materials, processes and systems, J. Wiley & Sons Inc., 2010.
• 6. Haddag B., Nouari M. and Mouf ki A.: Some cases of machining large-scale parts: characterization and modelling of heavy turning, deep drilling and broaching, AIP Conference Proc. 1716, AIP Publishing 2016, pp. 1-9.
• 7. Jang S.H, Choi Y.H., Kim S.T., An H.S., Choi H.B. and Hong J.S.: Development of core technologies of multi-tasking machine tools for machining highly precision large parts. Journal of the Korean Soc. for Precision Engineering, Vol. 29, No.2 (2012), pp. 129-138.
• 8. Kaliński K.J. and Galewski M.: Chatter vibration surveillance by the optimal-linear spindle speed control. Mechanical Systems and Signal processing, Vol. 25 (2011), pp. 383-399.
• 9. Lizarralde R., Azkarate A. and Zelaieta O.: New developments in lathes and turning centres, Chapter 7 in: Machine tools for high performance machining, Lopez de Lacalle L.N and Lamikiz A. (Eds), Springer-Verlag 2009.
• 10. Mares M., Horejs O. and Hornych J.: Advanced thermal error compensation of a flor type machining centre allowing for the influence of interchangeable spindle heads, Journal of Machine Engineering, Vol. 15, No. 3 (2015), pp. 19-32.
• 11. Matuszewski A. Musiał J. and Styp-Rekowski M.: Design and technological issues related to large parts of the modular structure (in Polish), Technologia i Automatyzacja Monażu, No. 2 (2012), pp. 28-30.
• 12. Neugebauer R., Wabner M., Rentzsch H. and Ihlenfeldt S.: Structure principles of energy efficient machine tools. CIRP Journal of Manufacturing Science and Technology, Vol. 4 (2011), pp. 136-147.
• 13. Onozuka H., Utsumi K., Kato T., Takahashi H. and Obikawa T.: Optimal design of a damped arbor for heavy duty machining of giant parts. Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol. 7, No. 2 (2013), pp. 171-186.
• 14. Ratchev T.M.: Concurrent process and facility prototyping for formation of virtual manufacturing cells. Integrated Manufacturing Systems, Vol. 12, No.4 (2010), pp. 306-315.
• 15. Siemiątkowski M. and Przybylski W.: Modelling and simulation analysis of process alternatives in the cellular manufacturing of axially symmetric parts. Intl. Journal of Advanced Manufacturing Technology, Vol. 32, Nos.5-6 (2007), pp. 516-530.
• 16. Simpson B. and Dicken P.J.: Integration of machining and inspection in aerospace manufacturing, IOP Conf. Series: Materials Science and Engineering, Vol. 26 (2011), pp. 1-4.
• 17. Uriarte L., Zatarain M., Axinte D., Yague-Fabra J., Ihlenfeldt S., Eguia J. and Olarra A.: Machine tools for large parts.CIRP Annals-Manufacturing Technology, Vol. 62 (2013), pp. 731-750.
• 18. Waiyagan K. and Bohez E.L.J.: Intelligent feature based process planning for five-axis multi-turn parts. Computers in Industry, Vol. 60 (2009), pp. 296-316.
• 19. Yao S., Han X., Yang Y., Rong Y., Huang S., Yen D. and Zhang G.: Computer aided manufacturing planning for mass customization: part 2, automated setup planning. Intl. Journal of Advanced Manufacturing Technology, Vol. 32 (2007), pp. 205-217.
• 20. Zhang, H-C. and Lin, E.: A hybrid-graph approach foe automated setup planning in CAPP. Robotics and Computer-Integrated Manufacturing, Vol. 15 (1999), pp. 89-100.
• 21. http://www.gospodarkamorska.pl/wydarzenia/wciagarka-z-energomontazu-polnoc-gdynia-dla-norweskiego-przemyslu-offshore.html, accessed on February 16th 2017.
• 22. http://en.nglmachining.com/park-maszynowy.html, accessed on February 16th 2017.

Identyfikatory

DOI

10.1515/pomr-2017-0019