The influence of manufacturing oversizing on post-welding distortions of the fillet welded joint

• Autorzy: Kozak J. , Kowalski J.
• Języki publikacji: EN

Abstrakty

EN

Welding proces is basic joining technique in shipbuilding. Such method generated welding distortions which cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work influence of oversizing of weld on angular distortions of joint is presented basing upon of the results of the laboratory measurements. Values determined on the basis of literature hypotheses are compared with the one obtained from the laboratory test

• Wydawca: -
• Czasopismo: Polish Maritime Research
• Rocznik: 2015
• Tom: 22
• Numer: 4
• Opis fizyczny: p.59-63,fig.,ref.

Twórcy

autor

Kozak J.

• Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology, Narutowicza 11/12 St., 80-233 Gdansk, Poland

autor

Kowalski J.

• Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology, Narutowicza 11/12 St., 80-233 Gdansk, Poland

Bibliografia

• 1. PRS Regulations, Principles for Welding Procedure Qualification Tests, Publication no. 74/p, 2007 (in Polish).
• 2. PRS Regulations, pt II Hull, 2014 (in Polish).
• 3. Wierzbicka : Overview and verification of formulas used to estimate angular distortions in a T-joint. Diploma thesis, Gdansk University of Technology, Faculty of Ocean Engineering and Ship Technology, 2014 (in Polish).
• 4. K. Ferenc, J. Ferenc: Welded structures – Joint design, Wydawnictwo Naukowo-Techniczne, Warsaw 2000 (in Polish).
• 5. Czajkowski H., Jakubiec M., Lesiński K., Technology of welded structures, Warsaw 1987 (in Polish).
• 6. Sędek P., Welding stresses and distortions, [in:] Engineer’s guidebook, Welding, t. I, ed. J. Pilarczyk, Warsaw 2003, pp. 559 -597 (in Polish).
• 7. Gourd L.M., Principles of welding technologies, transl. by N. Gawroniak, Warsaw 1997 (in Polish).
• 8. Predictive formulae for weld distortion – a critical review, Abington Publishing, 1999, ISBN 185573 444 3.
• 9. http://www.simufact.de/en/solutions/sol_weld.html (05.04.2014).
• 10. G. Jung, Plasticity-Based Distortion Analysis For Fillet Welded Thin Plate T-Joints, Dissertation, The Ohio State University 2003.
• 11. Ye Zhou, Analysis of Welding Distortions using Qualitative and Semi-quantitative Techniques, The University of British Columbia, 1998.
• 12. R.W.O’Brien, Predicting weld distortion in the design of automotive components, Durham theses, Durham University (2007). Available at Durham E-Theses Online: http://etheses.dur.ac.uk/2462/.
• 13. Kozak, J.Kowalski, Problems of Determination of Welding Angular Distortions of T-fillet Joints in Ship Hull Structures, Polish Maritime Research, ISSN: 1233-2585, 2015, vol.22, No2(86), 79-85
• 14. Czajkowski H., Jakubiec M., Lesiński K., Technology of welded structures, Warsaw 1987 (in Polish).
• 15. Engineer’s guidebook: welding. T. 1., Wydawnictwa Naukowo-Techniczne, Warsaw 2003 (in Polish).

Identyfikatory

DOI

10.1515/pomr-2015-0072